Applying VMAX NEW VX2 skins: Installation instructions

Before applying a VMAX VX2 skin, first clarify the generation and model version. This installation guide refers to the NEW VX2 range and uses the Camouflage Flecktarn design to show you how to assign the front and side panels.

Before you start: This orientation complements the instructions for your set. The instructions for the specific film supplied apply regarding cleaning agents, application temperature, bonding, and waiting time.

VMAX NEW VX2: does your set match the vehicle?

An older VX2 or VX2 PRO is not automatically equivalent to the NEW VX2. Furthermore, a shared fit for the NEW VX2 HUB and GEAR is not guaranteed without explicit product specification. Verify this information before peeling off the backing.

NEW VX2: generation first, camouflage parts later

The product view for Camouflage Flecktarn shows separate decals for the front transition, the angled frame section, and the deck side. The yellow reflector on the front must remain uncovered. Lay out the matching pre-cut parts with their backing paper onto these areas one by one. The irregular camouflage pattern is not a positioning marker: the decisive factors are the final contours, openings, and the outer edges of the actual surface.

VMAX NEW VX2 Camouflage Flecktarn with decal on frame and deck side and clear front reflector
Product view NEW VX2 Camouflage Flecktarn: use contours instead of camouflage spots for assignment. Existing AI-edited shop image; not a documented installation photo. The part assignment of your delivery is authoritative.

If you are not sure about the version, take a photo of the model name, both sides of the vehicle, and the area in question. Send these details along with your chosen design to our contact address. This allows the fit to be clarified specifically before a part has already been applied.

Applying VMAX NEW VX2 skins: six steps

Have the set, its instructions, a clean lint-free cloth, and the recommended squeegee ready. Use a squeegee with a soft edge protection only if it is suitable for the film.

  1. Prepare workspace. Switch off the scooter, disconnect the charger, and park the vehicle securely. Work in good lighting and under the conditions specified for the material.
  2. Clean and dry surfaces. Use a cleaning agent suitable for the substrate and the film. Also remove dirt from the edges. Do not apply to damp surfaces or loose coatings.
  3. Assign cut-outs. Test each part first while still on the backing paper. Use the contours, cut-outs, and model features described above. Clarify mismatched parts before peeling.
  4. Positioning. If dry application is required, peel back only a small area of the adhesive side first. Align the film without stretching. Use water only if explicitly approved for the set.
  5. Apply step-by-step. Peel off the backing paper gradually and smooth the film towards the free edge in a controlled manner. Only perform corrections and apply heat according to the processing instructions; do not trim on the scooter.
  6. Check finish. Inspect edges and cut-outs. Lights, reflectors, markings, controls, and moving parts must remain free. Observe the specified waiting time before use or cleaning.

Questions about installation on the VMAX NEW VX2

Can I treat HUB and GEAR the same due to similar photos?

Similar views do not confirm identical cut shapes. The authoritative factor is the explicit assignment of the ordered set to your NEW VX2 version.

Do the camouflage spots on the deck side have to match up?

Align the individual cut-outs according to their intended surfaces. Do not stretch or shift them in an attempt to make random spots continue across separate components.

Does this also apply to Carbon Blue Purple?

Model checks and preparation are equally necessary. Use the images of Carbon Blue Purple for the pattern flow and the instructions of your ordered version for the application. A different design does not mean a different model generation.

Designs and help for your VMAX NEW VX2

Is a part unclear? Ask an installation question regarding your VMAX NEW VX2 – state the design, exact model name, and the affected part. A photo with the backing paper still attached makes assignment easier.

Installation guides for other scooter models

EscooterSkins · As of: September 7, 2026. Basis: the sets and product views linked above. Material specifications and the instructions included with the delivery take precedence.